04 July 2015

Sailing New England and New York

Taking Off: Summery 2015

Time to Finally Do Some Real Sailing!

We have been quite sparse with the blogging this season and have featured mainly boat projects. Very cool boat projects in our opinion (Wifi, AIS, Davits) and we have been sailing but mainly just Boston Harbor and loops around the Islands except for a long haul to Newport in May to catch the Volvo Ocean Race whilst in town.  But now, we are in the early days of many weeks on the water - Aaaahhhhh :-).  Linda is fortunate to be entering a six week hiatus courtesy of Biogen's new mini sabbatical program.  Bob will spread out his more modest vacation time from Atlas by taking most Thursday's and Friday's off.

Pre trip dinner with two of the three boys, Jon and Christian

All provisioned with the new dinghy and new davits, ready to go!
Linda spent day 1 (July 1) provisioning, cleaning filters, filling water tanks, and preparing Argon for several weeks on the water whilst Bob hurriedly banged out more programming magic for Atlas.  We aimed to leave between 1400 and 1600 to ensure we could catch a positive current in the Cape Cod Canal.

Working on deadlines and averting craptastrophies.  Can you see the smoke coming out of his ears from all the serious programming?
We left Constitution Marina at 1600 Wednesday 1 July, motored over to Mystic Fuel to top of the tank and began our journey.  Bob was still working as we were underway leaving Boston Harbor.

Note the Bluetooth in his ear.  Bob had a 1630 teleconference that he took while we left the fuel dock.
Our new dinghy (Neon) and new davits with Boston in the background.  

Fantastic wind as we enter this first leg and prepare to sail through the night.
General Principles for this Sailing Trip

  • Maximize sailing to motoring ratio
  • Minimize pre-set "have to be x by y" and let the wind and our moods dictate where we go and when.  This being said, we have the following targets:
    • New York City / Liberty Landing (NJ side of Hudson) 5-9 July
    • Return to Boston approximately 23/24 July for a Tartan event at our marina before heading out again for another 10 days
    • Return to Boston again by 6 or 7 August to prepare to fly to Amsterdam (Joshua's wedding)
  • Relax, reflect, re-energize, and re-connect
Plan A:  (initial leg)
Practice longer haul sailing and associated shift changes between co-captains by sailing non-stop from Boston to Port Washington, NY (~40 hours and well over 200nm; Port Washington is on the western most part of Long Island just before Throgs Neck and entrance to the East River).  However, to stay true to General Principle #1 above we left plenty of time in our itinerary to allow for Plan B.

Plan B:
Wait for wind to minimize motoring - which proved to be needed.  

Boston to Cape Cod Canal was fantastic.  We also sailed nicely for the first many hours in Buzzards Bay, until we didn't.

Bob took the 2000 to 2400 shift while Linda slept bringing Argon to the mouth of the Cape Cod Canal in only 7.5 hours from Boston.  Wind was a perfect 12-15kts out of the southwest.  Gorgeous full moon.

Linda motored through a positive current in the Cape Cod Canal humming along over hull speed at 10+kts while Bob got some shut eye.  We were greeted by the expected headwind and churn coming out of the Canal which served to wake Bob from his rest.  But seas were calm ahead as Linda aimed high into a light SW wind averaging 5kts still under a brilliant full moon.  Sailing alone at night is a mixture of staying extremely alert and being calmly introspective.  

Watching the sun rise while sailing slowly in Buzzards Bay the morning of Thursday 2 July.
Fifteen hours in to our trip, we reluctantly took down the sails and began motoring.  After several hours of motoring, to stay true to General Principle 1, we tucked in to a cove in the western most part of Massachusetts to wait for the predicted better winds.  Alas, the wind data proved faulty and after hauling anchor, we toggled between motoring and slow sailing for many hours (mostly motoring unfortunately).  We decided to fully shift to Plan B and tuck in to beautiful West Harbor at Fisher Island.  

Brilliant sunset at anchor Fisher Island evening of Thursday 2 July.



Linda examined the wind and current forecasts and deemed a 0600 departure to be ideal.  We were both exhausted and slept soundly in this quiet harbor.  Thumbs up on Great Harbor Fisher Island.  

Pajama and coffee sailing 0630 hrs

Close reach in 10kts heading westward in Long Island Sound.

We hit 2000 nm on Argon west of Fisher Island.  We have a similar picture of us form last year (season 1 with Argon) when we hit 1000 nm east of Cape Cod Provincetown.  (When Bob saw this picture, he decided to shave and get a haircut.  See below.)
To prepare for his birthday, Bob shaved and Linda gave him a haircut while underway.  
The sailing from Fisher Island started out great.  We were taking advantage of the current doing 8kts in 11kts breeze close reach with the Genoa.  But then the wind died abruptly, as if someone just turned off the jets.  After motoring for another couple of hours with skepticism on the wind returning, we examined options and set a course for Port Jefferson.  So much for the non-stop long leg (Plan A) but we much prefer sailing over motoring and we still have flexibility in our timing (Plan B).

Port Jefferson Ferry shuttling passengers and vehicles between LI and CT.

Summer cottages dot the harbor.

Shallow Pirate Cove surrounded by interesting and lovely dunes.  We took the dinghy over and explored the dunes.  Really cool place (except for the broken glass that dotted the beach).





Very peaceful night except for a small group partying very loudly until wee hours of the morning.  It was quite comical to note the fitting name of the noisy boat the next morning. 

Happy Birthday, Bob!!!
Newly shaved and hair trimmed for his birthday today, July 4!!
After examining the wind and currents yesterday, we decided to leave Port Jefferson at 0800 for a 30  nm leg to Port Washington Manhasset Bay where we have a dock slip reserved for tonight to celebrate both Bob's birthday and the 4th.  The winds were as expected 8-12kts out of the east - perfect for a spinnaker run so we hoisted right away! We learned that our main is just too big and substantially interferes with spinnaker performance, at least in lighter winds. 

Nope, that's not right.

That's better!  A fantastic 30nm run to Manhasset Bay.
Soon we will be tied up to a dock slip celebrating Bob's birthday, the 4th of July, and the many blessings in our lives.

Below is a track of our journey to date, only the first four days.  Courtesy of Bob's Android and web service thingy.

03 July 2015

Automatic Identification System Installation

Still More Boat Projects: AIS


Linda got AIS for her birthday.

I ordered the Raymarine AIS650 and figured the installation would be pretty simple.  While waiting for it to arrive, I decided to read the installation manual. Ugh - you need a VHF splitter too. This is not some little cheap transformer thing either. It is a powered unit and adds a tidy $260 to the price.

So I ordered one of those.

What is AIS?
Automatic Identification System.  Ok, but what is that? AIS uses VHF to send and receive information about a boat: such as Name, Heading, Speed, Destination, Propulsion, Length and Beam. You can get a receiver only that will show other ships to you or a transceiver which will also broadcast your own signal to other ships.  This is what we got and since we may one day want to visit a foreign port, it required getting an FCC Ship's License. Every ship has a unique identifier called an MMSI number (don't ask).  Argon's is 367679020.

Installation
This should have been really simple.  We asked Tartan to put a SeaTalk backbone cable inside the instrument area above the nav table.  I assumed it was there.  It wasn't.  So I had to find another termination point on the backbone and run another cable. Fortunately, there was one in the aft compartment where the steering is. So off to West Marine to see if they had a SeaTalk backbone cable in stock.  Good news: they did.  Bad news(s): it was not quite the length I wanted and they did NOT have a network "T" in stock.  So, back to the internets to order more stuff.

Finally, with all the bits, the installation really did go very smoothly.




And it works.  Now that I have it, I can say that I wish ALL boats had it.  It is very nice to be able to see targets with bearing and speed.  Also, if you have to hail one, you can do it by name instead of "vessel over by blahdi-blah with the blue hull"

AIS On The Internets
There are several phone apps and websites that allow viewing AIS data. I think the way this works is that there is a network of receivers (volunteers?) who pick up AIS and repost it to various central data stores in reasonably real-time. I have not researched this. I could be totally wrong about that. As of this writing, we're still not showing up on the FindShip Android app, but we are now showing up on http://www.shipfinder.com/.  You can type our MMSI (367679020) into the search box and find us.

Update:  13-Jul-2015: we ARE now showing up on at least one AIS Phone App.  FindShip for Android is showing us. I would assume the various iPhone apps would show us too but I will become seasick if I have to touch an iOS device again. You can find us by name or MMSI


Davits and Dinghies

Another Boat Project: Davits


I hate the dinghy.  I like it for the 1% of the time we need it, but the other 99 is just a pain. There's just no good solution for any boat under 100' in my humble opinion. You either tow it, put it upside down on your deck, deflate it and store it, or lose your swim platform or... get davits.

We decided to get some davits from Kato Marine in Annapolis, MD.

The process is pretty simple. You have to figure out where you want them, measure a bunch of stuff and then like all things boating, hand over a few fist-fulls of cash.  I shouldn't be so cynical. Kato was awesome to work with and they made the process very smooth.  Once the order was finalized we waited for the big box of Kato parts to arrive.

Here are some photos of the mockups for measuring







Christmas on D-Dock
Thanks to UPS Saturday Delivery, we had our davits in time to install before our July trip.  The Kato parts are very high quality. We also had some custom designed stuff made for our installation and everything was very well made.











Getting to work
Time to drill 12 holes in Argon's Transom.  The installation actually went pretty smoothly.  We needed to change the location of the davits outboard a bit because of a contour in the interior of the hull. The flat backing plates would not have sat there very well.












11 June 2015

WiFi Installation on Your Boat


Captain Bob Damiano

Winter (and spring) (and summer) project: Argon gets WIFI


Since I live and work from the boat, good connectivity is pretty important.  We have a couple of 4G hotspots but those come with those annoying data plans. Our marina has free wifi (via Beacon) but all the cool kids put up wifi routers and have their own LANs on their boats.

So back in December, I decided to buy the stuff. I was going to buy a package from Island Time, but I thought I would be even cooler and buy the bits separately myself. That's a great idea if you're an IP/networking genius and can configure this stuff. So I got a Microtik Groove radio and router and started struggling with it (with lots of help from my boss, Dan who IS an IP/networking genius).

Ultimately, I ended up replacing the groove with a Ubiquity Bullet radio.  This thing is MUCH easier to configure and I was actually able to do it with some email support from boss Dan, brother Duane and brother Duane's friend Ralph.

So... I have a brand new Groove radio for sale if anyone wants it.


Physical Mounting

Argon has an Edson radar mast on her transom.  I spoke to someone at Edson and he suggested I buy this "wing" thing that mounts under the radar platform. This provides a nice surface to mount several small antennas.

To mount to that, I got a standard 1-14 antenna mounting base and an extension tube. 


1-14 base with "extra" hole
Using breakfast bar as machine shop
The original Groove radio (ultimately not used)

Wiring

The wireless router is installed inside the nav table instrument "pod".  I had to run a 12vdc line from a spare breaker to a new terminal block in there.  This feeds the router and the PoE (Power over Ethernet) injector to power the radio.

Terminal block for power

The new power/ground wires snaked into the breaker panel

Close-up of the Bullet

Router mounted.  Radio and antenna temporarily mounted for testing
We also had to run Ethernet all the way from the nav pod to the base of the radar mast and ultimately up the mast to the radio. 
Ethernet and wire snake

Linda doing best tie-wrap job ever down in the steering compartment
About now, is when I got the network to actually work. Until then, it was a notwork.

Putting it all together

This involved finalizing the mounting of the radio/anenna to the mount, unwiring the radar mast and removing it from the boat, installing all the stuff and hooking it all back up.  And then really really hoping that everything still works.


mounting the L-bracket to the extension tube


Bullet secured using a 'bulkhead" connector (and a couple big honkin washers)

Undo these wires at the base of the mast

Mast rail support removed and replaced with temporary measure

The stick is out

attaching the wing

We were smart enough to get help to re-install the stick.
 
And there she is.  DONE (finally)